Bulletproof Helmets Use Enhanced Fibers.

Apr 22, 2024

1,AROMAT

 

       The aromatic polyamide fibers used in the field of ballistic protection mainly include para-aramid (aramid 2) and heterocyclic aramid (aramid 3).

Para-aramid was first applied by the US Army in the field of ballistic protection. They used para-aramid as a reinforcing fiber to develop composite materials, replacing metal materials for manufacturing bulletproof helmets. Practice has shown that due to the excellent properties of para-aramid itself, such as ultra-high strength, high modulus, and low density, the ballistic performance of its composite materials is significantly better than that of steel helmets, while achieving lightweight bulletproof helmets.

 

         Currently, the most widely used bulletproof helmets in the world are still made of para-aramid. However, para-aramid also has certain defects. For example, under ultraviolet light exposure, the macromolecular chains of para-aramid will break, leading to a significant decrease in protective performance. Currently, industrially produced para-aramid products mainly include Kevlar from DuPont in the United States, Twaron from Teijin in Japan, Heracron from Kolon in South Korea, and Taparon from Yantai Tayho Advanced Materials Co., Ltd. in China.

 

        Structural modification of para-aramid can be carried out by introducing benzimidazole structure to develop heterocyclic aramid. Heterocyclic aramid not only has better mechanical properties than para-aramid but also improves the shortcomings of para-aramid's poor resistance to ultraviolet light, thus expanding its application range. China has developed bulletproof helmets made of heterocyclic aramid. Compared with para-aramid helmets with the same level of protection, their weight can be reduced by 20% to 30%.

 

2,UHMWPE fiber

 

          UHMWPE fiber came out in the 1970s. Its tensile strength is the highest among all industrialized high-performance fibers. Its strength exceeds aramid and its density is lower than aramid.

 

          At the beginning of the 21st century, in order to further reduce the mass of bulletproof helmets, the U.S. Army began to use UHMWPE fiber to research and develop bulletproof helmets. Since UHMWPE fiber has no large force between fiber molecules and no active groups on the surface, it is difficult to form a good bonding interface with the matrix when used as a composite reinforcement. Therefore, it is most often made into UD fabrics. Karthikeyan et al. used UHMWPE fiber and polyurethane to prepare UD fabrics, and found that the UD fabric with a lamination pattern of 0°/90° has the best ballistic performance.

 

          Currently, there are also studies on surface modification of UHMWPE fibers to improve the bonding properties of the interface with the resin matrix. Experimenters used a variety of physical and chemical methods to modify UHMWPE fibers. The study found that different modification methods have their own advantages and disadvantages: the electrical treatment method can achieve continuous modification treatment, but the surface bonding performance of the treated UHMWPE fiber The attenuation is serious; the plasma treatment method has a significant modification effect, but is expensive and difficult to process continuously; the chemical etching method is not environmentally friendly and can easily damage the mechanical properties of the fiber itself; the surface photografting modification method has little impact on the fiber properties and the modification The surface adhesion of the post-fiber fiber is significantly improved, but there are problems such as high cost and difficulty in continuous processing.

 

         In addition, the creep resistance of UHMWPE fiber is poor, and the ballistic-proof products made from them will have serious back dents after being impacted by ballistics. That is, the back of the ballistic-proof material will be dented after being deformed by the impact of a warhead. In response to this situation, the tensile modulus of UHMWPE fiber is increased by increasing the relative molecular weight and changing the drafting process, and reduces the problem of back concavity in its products.

 

 

Poly(p-phenylenebenzobisoxazole) (PBO) fiber and poly(2.5-dihydroxy-1,4-phenylenepyridinodiimidazole) (PIPD) fiber

 

 

          PBO fiber is a composite reinforcement material developed in the United States in the 1980s for the development of the aerospace industry.

Comparing the energy absorption of PBO fiber, aramid fiber, polyarylacetate fiber and carbon fiber composite materials, it was found that PBO composite materials can absorb more energy in penetrating impact and have great potential in the field of bulletproof energy absorption.

 

        Moreover, the creep resistance and modulus of PBO fiber also exceed that of most high-performance fibers used in the bulletproof field.

However, PBO fiber also has some problems as a reinforcing fiber for composite materials, such as intolerance to ultraviolet rays, poor compression resistance, and poor bonding performance with the resin interface. Therefore, it is not widely used in the bulletproof field.

 

       The molecular structures of PIPD fibers and PBO fibers are shown in Figure 4. It can be seen that the molecular structures of the two are similar, but the unique three-dimensional hydrogen bonding grid structure of PIPD fiber gives it better interface bonding performance, axial compression performance and greater tensile modulus.

11

 

           A comparison of the main performance parameters of several common high-performance fibers is shown in Table 1.

 

12

 

Hybrid fiber system

 

          With the development and changes of the times, people have higher and higher requirements for the bulletproof performance of bulletproof helmets, and single fiber-reinforced composite materials can no longer meet the protection needs of products. Various high-performance fibers have different characteristics, so hybrid fiber systems have gradually attracted attention. Hybridization is the mixing of high-performance fibers with different characteristics to prepare composite materials, which can give composite materials better properties. A good fiber mixing ratio and hybrid structural system can greatly improve the ballistic resistance of composite materials.

 

        Testers will mix para-aramid and heterocyclic aramid in different proportions, and use composite materials containing heterocyclic aramid as the ballistic surface and the back surface to conduct ballistic performance tests.

 

       The results show that when the composite material containing heterocyclic aramid is used as the ballistic surface, the ballistic limit velocity V50 is larger, and this is more obvious when the mass fraction of heterocyclic aramid in the composite is 30% to 70%. As the amount of heterocyclic aramid increases, the deformation of the bulletproof helmet after being hit decreases. The testers used UHMWPE composite materials and para-aramid fiber composite materials as the ballistic surface and back-end surface respectively to test the ballistic performance. The results showed that when UHMWPE composite material was used as the ball-end surface and para-aramid composite material was used as the back side, , when the ballistic protection performance is optimal, the mass ratio of UHMWPE composites and para-aramid composites is 50:50;

 

       When the para-aramid composite material is used as the front surface and the UHMWPE composite material is used as the back surface, the mass ratio of UHMWPE composite material and para-aramid composite material is 70:30 when the ballistic protection performance is optimal; the mass ratio of the hybrid structure composite material The ballistic performance is better than that of single fiber composite materials.

 

       Carbon fiber composites were used as the ballistic surface, and glass fiber composites and para-aramid composites were used as the back surface to prepare hybrid composite fabrics. After testing, it was found that the ballistic resistance of the obtained composite materials was better than pure carbon fiber, pure glass fiber and pure Single fiber composite made of para-aramid.

 

       At present, fiber hybrid systems have been put into use in large quantities. This hybrid fiber system, which can take advantage of different high-performance fibers, can help further improve the protective performance of ballistic protective equipment.

 

      (V50 refers to the bullet incident speed when the probability of bullet penetration into the test material is 50%. It quantifies the bulletproof performance of the material and is a reference index for evaluating the bulletproof performance of the material. The larger the V50, the better the bulletproof performance of the material.)