Research on friction characteristics between camouflage clothing and human elbow skin2

Apr 16, 2024

Experimental SectionExperimental Section

 

 

     1.1 Fabric Materials

      The fabric of camouflage clothing can be divided into various fibers such as pure cotton, polyester-cotton, viscose-cotton, and nylon-cotton based on fabric composition, and can be classified into plain weave (the warp and weft yarns interlace one up and one down) and twill weave (the warp and weft yarns interlace at least every two yarns) based on weaving method. In this experiment, four common types of camouflage clothing fabrics and the inner surface of one type of camouflage clothing underwear (worn inside the camouflage clothing as a short-sleeved undershirt) were selected as experimental materials. Each fabric was cut into approximately 5cmx5cm rectangles, and the knitting specifications of each fabric are listed in Table 1.

20240416174238

 

1.2 Skin Sites and Conditions

         During military training and combat, friction often occurs at sites such as the elbows, knees, and shoulders when soldiers perform tactical movements like lying prone, crawling, and overcoming obstacles. In this experiment, the outer skin of the elbows was selected as the test site because it is relatively flat and easy to manipulate. The elbow skin was sourced from 8 male volunteers with healthy skin and no existing skin conditions. The volunteers had an average age of 24 ± 2 years and an average weight of 60 ± 10 kg. The test sites on the outer elbows were approximately 20 cm from the bend of the arm. Volunteers were instructed not to use any skincare products on the day of the test. Before the experiment, the volunteers were briefed on the experimental procedures, processes, and potential risks.

 

 

1.3 Test Methods

        

        The surface morphology of camouflage clothing fabrics was observed using a three-dimensional laser confocal scanning microscope (LCSM, LS1100, Japan), and the hydrophobicity and hydrophilicity of the fabrics were measured using a DSA100 video contact angle measuring instrument (KRUSSR, Germany). Different camouflage clothing fabrics were tested for their frictional behavior with the skin under dry and wet conditions using a UMT-II multifunctional friction and wear tester (Bruker, USA). After friction, the skin was molded using silicone impression material (Coltex Rapid Liner) commonly used in dental clinics, and the roughness change of the skin before and after friction was measured using a three-dimensional laser confocal scanning microscope to observe skin damage.

 

       The test employed a reciprocating sliding motion with one side of the ball in contact, studying the frictional contact between the inner surface of the camouflage clothing fabric and the skin. Figure 1 illustrates the interface between the camouflage clothing and the human skin during frictional contact. Prior to the experiment, different camouflage clothing fabrics were wrapped around copper hemispheres with a diameter of 10 mm, which were connected to force sensors on the upper suspension system of the UMT-II.

   

       The upper arms of the participants were placed on a specially designed inclined cushion, keeping the outer skin of the elbows as horizontal as possible. Since friction between the camouflage clothing and the skin mainly occurs in the warp direction of the fabric, the reciprocating friction direction is consistent with the warp direction of the fabric. Military personnel are often required to move quickly and vigorously during tactical movements. Therefore, the frequency of friction at the fabric-skin interface is relatively high.

 

          For example, during crawling, the speed of military personnel is approximately 100-120 mm/s, and the frequency of each crawling action is approximately 1.8-2.4 Hz. Based on preliminary test results, the frequency (f) of reciprocating friction was set at 2 Hz, the reciprocating displacement (D) was set at 10 mm, and the reciprocating time was set at 15 minutes.

 

          Additionally, to simulate the sweat environment during continuous wear of camouflage clothing in combat training, 50 μL of artificial sweat was evenly applied within an area of approximately 5 mm × 10 mm at the test site using a microsyringe, with an additional 50 μL of artificial sweat added every 5 minutes to maintain the skin in a sweaty environment. The test sites were disinfected with alcohol after the experiment, and necessary medical treatment was administered to areas with superficial abrasions.

20240416174749